What is Bluetooth and how does it work?

What is Bluetooth and how does it work?

Bluetooth is today one of the most well-known wireless technologies. It is used for data transmission between devices over short distances. This technology uses UHF radio waves from 2.402 GHz to 2.480 GHz. Bluetooth was introduced on May 7th,1989. The present article shows how it works and how the connection is established.

How does Bluetooth work?

The Bluetooth standard, like WiFi, uses the FHSS technique (Frequency-Hopping Spread Spectrum), which involves splitting the frequency band of 2.402-2.480 GHz into 79 channels (called hops), each 1MHz wide. Then it transmits the signal using a sequence of channels known to both the sending and receiving stations.

Thus, by switching channels as often as 1600 times a second, the Bluetooth standard can avoid interference with other radio signals.

What is the Bluetooth communication principle?

The Bluetooth standard is based upon a master/slave operational mode. The term piconet refers to the network formed by one device and all devices found within its range. Up to 10 piconets can coexist within a single coverage area. A master can simultaneously connect to up to 7 active slave devices (255 when in parked mode). Devices in a piconet have a logical address of 3 bits for a maximum of 8 devices. Devices in parked mode are synchronized but do not have their physical address in the piconet.

Bluetooth: 1 master, 7 slaves

In reality, at a given moment, the master device can only be connected to a single slave at once. Therefore, it quickly switches between slaves to make it seem as if it is simultaneously connected to all the slave devices.

Bluetooth enables two piconets to be linked to one another to form a wider network, called a scatternet, using specific devices which act as a bridge between the two piconets.

How to establish connections via Bluetooth?

Establishing a connection between two Bluetooth devices follows a relatively complicated procedure meant to ensure a certain amount of security, as follows:

  • Passive mode.
  • Inquiry: Finding access points.
  • Paging: Synchronizing with access points.
  • Access point service discovery.
  • Creating a channel with an access point.
  • Pairing using PIN (security).
  • Using the network.

During normal use, a device operates in passive mode, meaning it listens to the network.

Establishing a connection begins with an inquiry phase, during which the master device sends an inquiry request to all devices found within its range, called access points. All devices that receive the query reply with their address. Then, the master device chooses an address and synchronizes with the access point using paging. This primarily involves synchronizing its clock and frequency with the access point.

After, a link with the access point is established, allowing the master device to enter an access point service discovery phase using a Service Discovery Protocol (SDP) protocol.

At the end of this service discovery phase, the master device is ready to create a communication channel with the access point using the protocol L2CAP.

Depending on the service's needs, an additional channel (called RFCOMM and operating over the L2CAP channel) may be established to provide a virtual serial port.

Some applications have been designed to connect to a standard port, independent of the hardware. For example, certain highway navigation programs have been designed to connect to any GPS Bluetooth device, such as earbuds.

The access point may include a security mechanism called pairing that restricts access to authorized users only to give the piconet a certain measure of protection. Pairing is done with an encryption key commonly known as a PIN (Personal Information Number). To do so, the access point sends a pairing request to the master device. Most of the time, this may prompt the user to enter the access point's PIN. If the PIN received is correct, the connection is made.

In secure mode, the PIN will be sent encrypted, using a second key, to prevent the signal from being compromised.

When the pairing becomes active, the master device is free to use the communication channel, thereby established.

What are Bluetooth profiles?

The Bluetooth standard defines a certain number of application profiles, called Bluetooth profiles, to define which kind of services a Bluetooth device offers. Thus, each device can support multiple profiles. Here is a list of the main Bluetooth profiles:

  • Advanced Audio Distribution Profile (A2DP)
  • Audio Video Remote Control Profile (AVRCP)
  • Basic Imaging Profile (BIP)
  • Basic Printing Profile (BPP)
  • Cordless Telephony Profile (CTP)
  • Dial-up Networking Profile (DUNP)
  • Fax Profile (FAX)
  • File Transfer Profile (FTP)
  • Generic Access Profile (GAP)
  • Generic Object Exchange Profile (GOEP)
  • Hard Copy Cable Replacement Profile (HCRP)
  • Hands-Free Profile (HFP)
  • Human Interface Device Profile (HID)
  • Headset Profile (HSP)
  • Intercom Profile (IP)
  • LAN Access Profile (LAP)
  • Object Push Profile (OPP)
  • Personal Area Networking Profile (PAN)
  • SIM Access Profile (SAP)
  • Service Discovery Application Profile (SDAP)
  • Synchronization Profile (SP): used to synchronize the device with a personal information manager (or PIM for short).
  • Serial Port Profile (SPP)
do you have more questions about bluetooth? check out our forum!
Around the same subject