Problem to Install Windows XP
Closed
meiax93
Posts
2
Registration date
Monday February 27, 2012
Status
Member
Last seen
February 28, 2012
-
Feb 27, 2012 at 10:00 AM
meiax93 Posts 2 Registration date Monday February 27, 2012 Status Member Last seen February 28, 2012 - Feb 28, 2012 at 08:50 AM
meiax93 Posts 2 Registration date Monday February 27, 2012 Status Member Last seen February 28, 2012 - Feb 28, 2012 at 08:50 AM
Related:
- Problem to Install Windows XP
- Kmspico windows 10 - Download - Other
- Install md5sum windows - Guide
- Gta 5 download apk pc windows 10 - Download - Action and adventure
- Windows 10 iso download 64-bit - Download - Windows
- Windows xp sp3 download - Download - Windows
2 responses
xpcman
Posts
19528
Registration date
Wednesday October 8, 2008
Status
Contributor
Last seen
June 15, 2019
1,824
Feb 27, 2012 at 12:52 PM
Feb 27, 2012 at 12:52 PM
Here's a possible solution if you're in this kind of SATA hard drives not found situation. The trick is related to ACHI (Advanced Host Controller Interface) hardware mechanism which are designed to allow software to communicate with Serial ATA (SATA) devices such as host bus adapters with features not offered by Parallel ATA (PATA) controllers such as higher speeds, hot-plugging and native command queuing (NCQ). Windows XP (and any OS older than Vista or linux kernel 2.6.19) does not have came pre-packaged with driver to support AHCI/SATA mode, thus creating a very common error that Wikipedia also described as "when attempting to install Microsoft Windows XP or a previous version on an AHCI-enabled system will cause the setup to fail with the error message `set up could not detect hard disk drive...'".
The ultimate solution is by using OEM Windows XP CD which comes with your system, which usually has built-in appropriate driver for S-ATA harddisks running in AHCI mode. However, if you lose or do not have the OEM XP CD, or is given Vista DVD but decide to downgrade to XP, there are 2 options to install XP from scratch.
Users can install Windows XP or Windows XP SP2 (Service Pack 2) on an AHCI enabled system by changing BIOS setting to disable AHCI (or RAID which includes AHCI in its functions) and use native SATA IDE emulation mode (SATA/PATA). In SATA IDE Emulation mode, XP setup could find the SATA drives and proceed to continue to install XP properly. How to change the BIOS settings on SATA mode is depending on which brand or model or even motherboard of your computer system. Check your system manual for more information. For example, in Dell Precision workstation, press F2 to go into BIOS, and then go to "SATA Management" to select AHCI or SATA mode. If you don't find any option in BIOS to change AHCI support for SATA ports, most probably the drives already runs in IDE (ATA) emulation mode and therefore doesn't require the AHCI driver. It's because AHCI support is depending on the chipset (commonly by Intel) and the HDD. In this case, you have to figure out what's other causes that may stop your SATA disks from functioning.
A slightly more difficult but recommended method is to create a slipstreamed XP install disc with the Intel Matrix Storage Manager which is also the AHCI SATA Controller driver included. A slipstreamed XP setup CD with AHCI SATA controller driver allows the XP OS to support hard disk on AHCI and use its advanced features such as NCQ for faster access, read and write speed. While slipstreaming, users can also have the advantage to include all updates for Windows XP for up-to-date patched OS, without the need to download and install hotfixes later.
Related posts:
The ultimate solution is by using OEM Windows XP CD which comes with your system, which usually has built-in appropriate driver for S-ATA harddisks running in AHCI mode. However, if you lose or do not have the OEM XP CD, or is given Vista DVD but decide to downgrade to XP, there are 2 options to install XP from scratch.
Users can install Windows XP or Windows XP SP2 (Service Pack 2) on an AHCI enabled system by changing BIOS setting to disable AHCI (or RAID which includes AHCI in its functions) and use native SATA IDE emulation mode (SATA/PATA). In SATA IDE Emulation mode, XP setup could find the SATA drives and proceed to continue to install XP properly. How to change the BIOS settings on SATA mode is depending on which brand or model or even motherboard of your computer system. Check your system manual for more information. For example, in Dell Precision workstation, press F2 to go into BIOS, and then go to "SATA Management" to select AHCI or SATA mode. If you don't find any option in BIOS to change AHCI support for SATA ports, most probably the drives already runs in IDE (ATA) emulation mode and therefore doesn't require the AHCI driver. It's because AHCI support is depending on the chipset (commonly by Intel) and the HDD. In this case, you have to figure out what's other causes that may stop your SATA disks from functioning.
A slightly more difficult but recommended method is to create a slipstreamed XP install disc with the Intel Matrix Storage Manager which is also the AHCI SATA Controller driver included. A slipstreamed XP setup CD with AHCI SATA controller driver allows the XP OS to support hard disk on AHCI and use its advanced features such as NCQ for faster access, read and write speed. While slipstreaming, users can also have the advantage to include all updates for Windows XP for up-to-date patched OS, without the need to download and install hotfixes later.
Related posts:
meiax93
Posts
2
Registration date
Monday February 27, 2012
Status
Member
Last seen
February 28, 2012
Feb 28, 2012 at 08:50 AM
Feb 28, 2012 at 08:50 AM
In BOOT MENU HP Compaq NX6330 i see dont have AHCI/IDE menu,
it's have some like LBA (something) and Bit-(something)
no problem to delete partition,formatting,and finish setup.
On next step, after formating, must restart right?
it not continue install ( after restart, will appear windows loading, and puff appear setup ) but in my case it dont appear.
actually i want install windows 7 cannot..=="
but, if can, i want install windows XP.
p/s : sry my english bad =(
it's have some like LBA (something) and Bit-(something)
no problem to delete partition,formatting,and finish setup.
On next step, after formating, must restart right?
it not continue install ( after restart, will appear windows loading, and puff appear setup ) but in my case it dont appear.
actually i want install windows 7 cannot..=="
but, if can, i want install windows XP.
p/s : sry my english bad =(
