Previous Topic Next Topic

Pc turns on but no signal message on screen

Solved/Closed
bob1679 Posts 4 Registration date Monday July 22, 2013 Status Member Last seen July 23, 2013 - Jul 22, 2013 at 03:29 PM
bob1679 Posts 4 Registration date Monday July 22, 2013 Status Member Last seen July 23, 2013 - Jul 23, 2013 at 06:26 AM
hi all my pc crashed this morning so i turned it off and back on but it would not give signal to the screen . there are no beeps from it it just lights up and the fans spin . i seen somewhere to remove the ram so done that and it makes a constant beep noise . i also noticed there is no light on the motherboard . i have tryed removing the bios battery but no diffrence can anyone please help us out young family really need this fixed please help if you can
Related:

1 response

Answer 1 / 1
jack4rall Posts 6428 Registration date Sunday June 6, 2010 Status Moderator Last seen July 16, 2020
Jul 22, 2013 at 06:52 PM
Hello,

Try this 1

If you notice that your CPU fan is running but there is no display in the screen,

then remove the RAM from the slot, clean it and place it back properly or try

another slot.

Check your RAM also. Even bad RAM will result in display problem.

If you are having two RAMs then remove it, place only one RAM and check the

display. If you failed to get any display then change the slot. If you still failed to

get the display then try the above procedure with the other RAM.

Good Luck
0
bob1679 Posts 4 Registration date Monday July 22, 2013 Status Member Last seen July 23, 2013
Jul 23, 2013 at 03:17 AM
hi i have tryed that already do you think there may be somthing else it may be . when i removed the ram i switched it back on and the board beeps but that is the only time it dose it i have tryed removing everthing but nothing happens
0
jack4rall Posts 6428 Registration date Sunday June 6, 2010 Status Moderator Last seen July 16, 2020
Updated on Nov 28, 2018 at 12:19 PM
Hello,
Try this 1
1) Make sure that the problem is not with the RAM. Even bad RAM will result in display problem.
2) Once again try to reset your CMOS settings.
Turn off your PC and remove the power chord --> Open the cabinet --> Remove the CMOS battery for 15-30 minutes and then put it back properly. Now plug the power cord back in and switch ON your PC.
Click on the below hyperlink "CMOS Battery" if you don't have any idea about the CMOS battery
CMOS Battery
If the problem still exist, click on the below link and follow the instructions in "Hardware Reset".
https://ccm.net/faq/1192-lost-bios-password-resetting-the-bios
3) Remove all the connections from the motherboard --> Remove all the dust from the motherboard and also make sure that there is no dust underneath of motherboard. Then connect all the connections back.
4) Check if you are able to see the LED on the keyboard in ON state.
Good Luck
0
bob1679 Posts 4 Registration date Monday July 22, 2013 Status Member Last seen July 23, 2013
Jul 23, 2013 at 06:17 AM
thanks for your help but i now am thinking my motherboard has died there is no out put what so ever from it none of the usbs work only thing that works is the 3 fans and the hard drive key board and mouse dont work either now and i have tryed the bios battery and the jumper thing aswell
0
jack4rall Posts 6428 Registration date Sunday June 6, 2010 Status Moderator Last seen July 16, 2020
Jul 23, 2013 at 06:20 AM
Hello,
If you failed to see any display, LED on the keyboard and mouse is OFF then the problem might be with the motherboard. There might be a component on the motherboard that got damaged.
Good Luck
0
bob1679 Posts 4 Registration date Monday July 22, 2013 Status Member Last seen July 23, 2013
Jul 23, 2013 at 06:26 AM
thanks very much for you help think i will just try and buy another pc to much hassle replacing motherboards lol
0

Similar discussions

LG monitor says D-sub no signal
Servant-Of-SSRR -
dinesh -

15 responses